He Velocity Figure 6 shows the isosurface diagram in the molten steel
He Velocity Figure 6 shows the isosurface diagram from the molten steel (Vsteel = 0.two m/s) with and without having FAC-EMBr. In the very same time, the distributions on the steel/slag interface below the situation of Case 1 had been also displayed within the figure.p = -15and the SEN immersion depth DSEN = 180 mm. three.two.1. Impact of SEN Position and Magnetic Field around the VelocityProcesses 2021, 9,Figure 6 shows the isosurface diagram of the molten steel (Vsteel = 0.two m/s) with and without the need of FAC-EMBr. At the identical time, the distributions of the steel/slag interface 6 of 13 under the condition of Case 1 have been also displayed within the figure.(a)(b)Figure 6. Distribution of velocity isosurface 0.2 m/s) and steel/slag interface beneath Case 1. Figure six. Distribution of velocity isosurface (V(Vsteel =0.2 m/s) and steel/slag interface below Case 1. steel = A; A; IVP-I and IHP = 350 = (a) IVP-I = IIVP-II = IHP = 0 = 0 (b) (b) I= IVP-II = 250 A 250 A and I A. 350 A. (a) IVP-I = VP-II = IHP VP-I = IVP-II = HPAs shown in Figure six, in the case without the application of FAC-EMBr, the flow As shown in Figure 6, in the case with no the application of FAC-EMBr, the flow velocity in the impact region, the reduce recirculation region, plus the meniscus region all velocity within the effect region, the lower recirculation area, as well as the meniscus area all attain 0.two m/s. The impingement depth the (Z)-Semaxanib Protocol decrease backflow area is comparatively massive, and reach 0.2 m/s. The impingement depth of in the reduced backflow area is somewhat massive, and the velocity isosurface is asymmetrically distributed z the z = 0 section. The asymthe velocity isosurface is asymmetrically distributed within the in= 0 section. The asymmetric metric distribution of velocity forms which can be not conducive conducive towards the floating distribution of velocity types bias flow,bias flow, which is to not the floating removal of removal and bubbles, and quickly types defects in the slab [12]. At slab [12]. In the can inclusionsof inclusions and bubbles, and quickly types defects in the the exact same time, itsame time, it could be discovered that, when the C6 Ceramide Apoptosis FAC-EMBr could be the molten the molten steel velocity in be discovered that, when the FAC-EMBr is just not applied,not applied, steel velocity within the upper the upper backflow and meniscus regions are as well lead which lead slag layer being backflow and meniscus regions are as well substantial, whichlarge, for the liquid to the liquid slag pushed away by molten steelmolten steel (forming slag holes).At this time, theoxidation layer getting pushed away by (forming slag holes).At this time, the secondary secondary occurs when the high-temperature molten steel contactssteeland ultimately theand finallythe oxidation occurs when the high-temperature molten air, contacts air, quality of the continuous the continuousreduced.slab is reduced. On account of the asymmetric arrangement of high-quality of casting slab is casting Because of the asymmetric arrangement of the SEN in the thickness path, the breakout areathealso closer region iswide closer to the wide face. With the SEN inside the thickness direction, is breakout towards the also face. With all the application of FAC-EMBr, the velocity in the upward backflowthe upward backflow and meniscus regions the application of FAC-EMBr, the velocity in and meniscus regions have been all significantly reduced, and the slag holes were along with the slag holes have been also eliminated. The [24] was have been all considerably lowered, also eliminated. The meniscus wave height y meniscus lowered from 41.2[24] was reduced fromthe brake effect ofmm.